Inspections for race week

2026 Inspection Results

Welcome to the 2026 Inspections page for the 88th Soap Box Derby World Championships! We have exciting news to kick off the festivities. As of July 12 at 5 p.m., we have officially processed several VIP results and posted the link to them below. Moving forward, we will update this page at least two more times before Saturday morning to keep you fully informed. In the meantime, we want to extend a huge thank you to all the champs who dropped off their cars early, as well as to our inspectors for their incredible hard work.

Looking ahead, as soon as we finish all inspections, we will immediately post the finals for the Champs listed below.

Please Note: If your car shows VIP status, you must still complete additional requirements (such as nose height, nose screws, and shell flush) during the shell attach on Sunday to maintain that VIP status.

ALL 14 Legacy cars are VIP !

Car No. = 10,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> HORSE SHOE NEEDSTO BE ATTACHED
   Failed item 8. “Shell Cutout, Sides of shell must be padded with 3/8 inch thick foam”.   Reason -> NEEDS FOAM
   Failed item 19. “Alternate Rear Axle Mounting Assembly, Installed w/carriage or hex bolts and nuts AASBD issued”.   Reason -> NOT PER PLANS
   Failed item 30. “Foils, AASBD issued”.   Reason -> REMOVE AND USE CURRENT/CORRECT AIRFOILS

Car No. = 11,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> DOES NOT MEET 7-1/4

Car No. = 12,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> DOES NOT MEET 7-1/4

Car No. = 13,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 14,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 15,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 15. “Axle Mounting Plates, AASBD issued. AASBD logo must be visible”.   Reason -> REAR MISSING LOCKWASHER
   Failed item 33. “Adjustable, 10 pounds minimum (with wing nuts)”.   Reason -> WEIGHT PLATE OVER 12″ AND TOUCHING

Car No. = 16,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 17,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 7. “Helmet Cutout, 7 inches wide to first rivet”.   Reason -> DOES NOT MEET 7
   Failed item 18. “Angle Iron Rear Axle Mounting Assembly, Installed per plan”.   Reason -> REMOVE
   Failed item 32. “Bolts, 5/16 inch bolts”.   Reason -> CUT CENTER WEIGHT BOLT OR ADD WEIGHT
   Failed item 36. “Title/National Sponsor(s),  “.   Reason -> NEEDS DECAL

Car No. = 18,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 19,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 20,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 22,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 23,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 24,    Local,    Master    NON VIP
   Failed item 1. “Girth, 36-1/2 inches minimum, at hatch hinge”.   Reason -> VIP AFTER SHELL MOUNTED
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 25,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 26,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 7. “Helmet Cutout, 7 inches wide to first rivet”.   Reason -> SEVERAL SHARP POINTS NEED TO BE CORRECTED
   Failed item 21. “Turning Radius, 3/8 inch minimum, 1 inch maximum each direction”.   Reason -> CORRECT STEERING – TURNING THE WRONG WAY

Car No. = 27,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 28,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 29,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 9. “Hinge, AASBD issued”.   Reason -> REMOVE SIDE CLIPS OR SHORTEN TO MEET SPEC.
   Failed item 32. “Bolts, 5/16 inch bolts”.   Reason -> PAD BACK WEIGHT BOLT

Car No. = 30,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 18. “Angle Iron Rear Axle Mounting Assembly, Installed per plan”.   Reason -> WRONG BOLTS – USED ROUND HEAD NOT HEX HEAD

Car No. = 31,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 32,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 33,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 34,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 35,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> DOES NOT MEET 7-1/4
   Failed item 28. “Logo and Date, Axle Logo and date must be visible”.   Reason ->

Car No. = 36,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 37,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 500,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 501,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 15. “Axle Mounting Plates, AASBD issued. AASBD logo must be visible”.   Reason -> REPLACE BOTTOM PLATE-CAN NOT BE ALTERED
   Failed item 33. “Adjustable, 10 pounds minimum (with wing nuts)”.   Reason -> FIX CHAINED WEIGHT IN FRONT

Car No. = 502,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 503,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 24. “Brake Facing, New AASBD brake pad installed”.   Reason -> REPAIR CABLE KEEPER
   Failed item 33. “Adjustable, 10 pounds minimum (with wing nuts)”.   Reason -> TOOLONG UNDER BACK (12-3/8)

Car No. = 504,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 505,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> IS NOT 7-1/4
   Failed item 18. “Angle Iron Rear Axle Mounting Assembly, Installed per plan”.   Reason -> NEEDS LOCK WASHER ON REAR

Car No. = 507,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 5. “Helmet, First rivit must be visible”.   Reason -> NEEDS ANOTHER HELMET
   Failed item 33. “Adjustable, 10 pounds minimum (with wing nuts)”.   Reason -> CHANGE WEIGHT IN FRONT (VIP AFTER IT HAS BEEN CHANGED)

Car No. = 508,    Local,    Master    NON VIP
   Failed item 1. “Girth, 36-1/2 inches minimum, at hatch hinge”.   Reason -> NEEDS TO CHECK AFTER SHELL ATTACHMENT – IF OK WILL BE ISSUED A VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 511,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 512,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> NOT 7-1/4″

Car No. = 513,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 514,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 515,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 516,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 517,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 518,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 18. “Angle Iron Rear Axle Mounting Assembly, Installed per plan”.   Reason -> NOT PER PLAN USED ROUND HEAD NEEDS TO BE HEX

Car No. = 519,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 17. “Kingpins, AASBD issued kingpins and bushings only”.   Reason -> NEED “N” WASHER ON BOTTOM OF KINGPIN

Car No. = 520,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 521,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 522,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 523,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 524,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 525,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 526,    Local,    Master    NON VIP
   Failed item 1. “Girth, 36-1/2 inches minimum, at hatch hinge”.   Reason -> SHELL NEEDS RAISED VIP AFTER MEASURED
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 527,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 528,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> NOT 7-1/4

Car No. = 529,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 530,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 29. “Kingpins, 3-1/2″ or 3-1/4″ inch grade 8 and must be visible”.   Reason -> NEEDS “N” WASHER AT FRONT KINGPIN

Car No. = 531,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 532,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 533,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 534,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 535,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 536,    Local,    Master    VIP   But the following will be checked after shell installation
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!

Car No. = 537,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> DOES NOT MEET 7-1/4″

Car No. = 539,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 9. “Hinge, AASBD issued”.   Reason -> REMOVE SOME FILLER INSIDE AT HINGE
   Failed item 23. “Brake Pedal, 3/4 inch plywood or pivot style brake”.   Reason -> NEEDS NEW PAD

Car No. = 904,    Local,    Master    NON VIP
   item 2. “Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum”.   Reason -> Check after body installed !!
   Failed item 6. “Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits”.   Reason -> DOES NOT MEET 7-1/4″

Car No. = 301,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 302,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 303,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 304,    Local,    Stock    NON VIP
   Failed item 13. “Bushing installed per plans, Photos 6.7”.   Reason -> WRONG STABLIZER BOLTS
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!
   Failed item 40. “Coatings with tung oil and/or wax,  “.   Reason -> NEEDS NEW FLOORBOARD – FLOORBOARD WAS ALTERED

Car No. = 305,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 306,    Local,    Stock    NON VIP
   Failed item 8. “Cable pulley hardware per plans, Photo 5.6 “.   Reason -> WRAP NOT PER PLAN
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> BRAKE PLUNGER EYEBOLT NOT PER PLAN
   Failed item 23. “Adjustable weight hardware per plans, Photo 9.10”.   Reason -> LEAD WEIGHTS NEED TO BE PAINTED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 307,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 308,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 309,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 310,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 311,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 312,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 314,    Local,    Stock    NON VIP
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> BRAKE PEDAL NEEDS TO BE MOVED FORWARD INTO BRAKE AREA
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 315,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 316,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 317,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 318,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 319,    Local,    Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.38(a) & (b) “.   Reason -> WRAP NOT PER PLAN
   Failed item 16. “New brake pad installed,  “.   Reason -> NEEDS NEW BRAKE PAD
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> WEIGHTS NEED TO BE FLUSH ON FLOORBOARD
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 320,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 322,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 323,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 324,    Local,    Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.38(a) & (b) “.   Reason -> NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 325,    Local,    Stock    NON VIP
   Failed item 14. “Stock radius rod assembly per plans, Photos 6.16, 6.19, 6.23 & 6.26 “.   Reason -> NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 326,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 327,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 328,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 329,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 330,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 331,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 332,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 333,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 334,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 335,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 336,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 337,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 338,    Local,    Stock    NON VIP
   Failed item 7. “Cable pulleys installed per plans, Photos 5.6”.   Reason -> LEFT FRONT STEERING PULLEY NEEDS “N” WASHER
   Failed item 18. “Cable pulley installed per plans, Photo 8.24”.   Reason -> BRAKE PULLEY WASHER SPACER NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 339,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 340,    Local,    Stock    NON VIP
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!
   Failed item 34. “Holes in shell for attachment to floorboard must not be altered,  “.   Reason -> HOLES CANNOT BE ALTERED – NEEDS A NEW SHELL

Car No. = 341,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 342,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 343,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 344,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 345,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 346,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 348,    Local,    Stock    NON VIP
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> CAN NOT BE LANGER THAN 12″
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 349,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 350,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 351,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 352,    Local,    Stock    NON VIP
   Failed item 1. “Steering stop hareware per plans, Photo 1.3”.   Reason -> BOLTS NOT PER PLAN
   Failed item 6. “Steering hardware per plans, Photos 4.6, 4.10(a) & (b) “.   Reason -> STEERING PULLEY HARDWARE NOT PER PLAN
   Failed item 20. “Awning pulley hardware per plans, Photo 8.41”.   Reason -> REMOVE EXTRA WASHER FROM AWNING PULLEY
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 353,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 354,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 357,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 358,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 359,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 360,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 700,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 701,    Local,    Stock    NON VIP
   Failed item 8. “Cable pulley hardware per plans, Photo 5.6 “.   Reason -> REMOVE “N” WASHER FROM UNDERNEATH STEERING PULLY
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> REMOVE WEIGHT FROM NO WEIGHT ZONE IN FRONT OF CAR
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 702,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 704,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 705,    Local,    Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.38(a) & (b) “.   Reason -> STEERING NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 707,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 708,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 709,    Local,    Stock    NON VIP
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> FIXED WEIGHTS CAN NOT BE LONGER THAN 12 “
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 710,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 711,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 712,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 713,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 715,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 716,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 718,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 719,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 720,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 721,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 723,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 724,    Local,    Stock    NON VIP
   Failed item 2. “Foot brace hardward per plans, Photo 2.5”.   Reason -> MISSING FOOT BRACE
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> EYE BOLT NOT PER PLAN
   Failed item 20. “Awning pulley hardware per plans, Photo 8.41”.   Reason -> NOT PER PLAN
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> ACORN NUTS NOT PERMITTED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 725,    Local,    Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.38(a) & (b) “.   Reason -> NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 726,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 727,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 728,    Local,    Stock    NON VIP
   Failed item 2. “Foot brace hardward per plans, Photo 2.5”.   Reason -> WRONG WASHERS ON FOOT BRACE
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> BRAKE PAD BOLTS NEEDS TO BE TIGHTEN – BRAKE PEDAL MAY NOT BE ALTERED – REMOVE EXTRA WASHER ON BRAKE PULLY
   Failed item 20. “Awning pulley hardware per plans, Photo 8.41”.   Reason -> PULLY BOLT NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 729,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 730,    Local,    Stock    NON VIP
   Failed item 2. “Foot brace hardward per plans, Photo 2.5”.   Reason -> NEEDS FOOT BRACE
   Failed item 14. “Stock radius rod assembly per plans, Photos 6.16, 6.19, 6.23 & 6.26 “.   Reason -> NEEDS “N” WASHER ON STABILIZER
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> WEIGHTS BOLTS NEED TO BE CUT
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 731,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 732,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 735,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 736,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 737,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 738,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 740,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 741,    Local,    Stock    NON VIP
   Failed item 1. “Steering stop hareware per plans, Photo 1.3”.   Reason -> MUST BE AASBD ISSUED
   Failed item 20. “Awning pulley hardware per plans, Photo 8.41”.   Reason -> REMOVE EXTRA “N” WASHER FROM AWNING PULLEY
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!
   Failed item 40. “Coatings with tung oil and/or wax,  “.   Reason -> NEEDS NEW FLOORBOARD – FLOORBOARD CAN NOT BE ALTERED

Car No. = 742,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 743,    Local,    Stock    NON VIP
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> BRAKE PEDAL CAN NOT BE ALTERED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 744,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 745,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 746,    Local,    Stock    NON VIP
   Failed item 5. “Rear kingpin washer stack per plans, Photo 3.19 “.   Reason -> WASHER STACK NOT PER PLAN
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> CAN NOT BE LARGER THAN 12
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R703,    Rally,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R714,    Rally,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R717,    Rally,    Stock    NON VIP
   Failed item 14. “Stock radius rod assembly per plans, Photos 6.16, 6.19, 6.23 & 6.26 “.   Reason -> NEEDS 2 N WASHERS UNDER STABILIZER
   Failed item 18. “Cable pulley installed per plans, Photo 8.24”.   Reason -> NEEDS NEW SPACER/CANNOT BE ALTERED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R722,    Rally,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R733,    Rally,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R734,    Rally,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = R739,    Rally,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 101,    Local,    Super Stock    NON VIP
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   Failed item 33. “No overspray on inside of shell,  “.   Reason -> REMOVE OVERSPRAY

Car No. = 102,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 103,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 104,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 105,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 106,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 107,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 108,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 109,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 110,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 111,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 112,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 113,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 114,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 115,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 116,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 117,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 118,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 120,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 121,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 122,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 123,    Local,    Super Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> WRAP NOT PER PLAN/SEE AN OFFICAL
   Failed item 18. “Cable pulley installed per plans, Photo 8.24”.   Reason -> BRAKE PULLEY NEEDS LOCK WASHER
   Failed item 19. “Brake plunger installed per plans, Photos 8.26 & 8.30”.   Reason -> EYEBOLT NEEDS LOCK WASHER
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 124,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 125,    Local,    Super Stock    NON VIP
   Failed item 2. “Foot brace hardward per plans, Photo 2.5”.   Reason -> REPLACE BRACE/HAS BEEN SHAVED
   Failed item 7. “Cable pulleys installed per plans, Photos 5.6”.   Reason -> “N” WASHERS SHOULD BE UNDER PULLEYS
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> STEERING CABLE WRAPPED WRONG
   Failed item 19. “Brake plunger installed per plans, Photos 8.26 & 8.30”.   Reason -> WRONG EYE BOLT ON PLUNGER
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   Failed item 35. “Shell decals and decorations per plans, Photo 13.1 (all views) “.   Reason -> TRIM WRAP/CANNOT COVER SCREW HOLES

Car No. = 126,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 127,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 128,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 129,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 130,    Local,    Super Stock    NON VIP
   Failed item 23. “Adjustable weight hardware per plans, Photo 9.10”.   Reason -> REMOVE WEIGHTS OUT OF THE NO-WEIGHT AREA
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 131,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 132,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 133,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 134,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 135,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 136,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 137,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 138,    Local,    Super Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> WRAP NOT PER PLAN
   Failed item 14. “Stabilizer assembly per plans, Photos 6.7, 6.8, 6.11, 6.19 “.   Reason -> REAR SHIM MUST BE REMOVED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 139,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 140,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 141,    Local,    Super Stock    NON VIP
   Failed item 4. “Front kingpin washer stack per plans , Photo 3.19”.   Reason -> FRONT KINGPIN WASHER STACK NOT PER PLAN
   Failed item 7. “Cable pulleys installed per plans, Photos 5.6”.   Reason -> STEERING CABLE PULLYS NEEDS FENDER WASHERS
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> STEERING NOT PER PLAN
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> BRAKE PEDAL NEEDS TO BE TIGHTEN
   Failed item 18. “Cable pulley installed per plans, Photo 8.24”.   Reason -> BRAKE PULLY BOLT/WASHER NOT PER PLAN
   Failed item 23. “Adjustable weight hardware per plans, Photo 9.10”.   Reason -> LEAD WEIGHTS NEEDS TO BE PAINTED
   Failed item 28. “Front foam installed per plans, Photo 12.4 “.   Reason -> FOAM NEEDS TO BE REGLUED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   Failed item 33. “No overspray on inside of shell,  “.   Reason -> REMOVE OVERSPRAY FROM INSIDE OF BODY

Car No. = 142,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 143,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 144,    Local,    Super Stock    NON VIP
   Failed item 14. “Stabilizer assembly per plans, Photos 6.7, 6.8, 6.11, 6.19 “.   Reason -> NOT PER PLAN-NEEDS 2” WASHER
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 145,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 146,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 147,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 148,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 149,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 150,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 151,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 152,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 153,    Local,    Super Stock    NON VIP
   Failed item 14. “Stabilizer assembly per plans, Photos 6.7, 6.8, 6.11, 6.19 “.   Reason -> REAR STABILIZER NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 154,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 155,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 156,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 157,    Local,    Super Stock    NON VIP
   Failed item 14. “Stabilizer assembly per plans, Photos 6.7, 6.8, 6.11, 6.19 “.   Reason -> REAR STABLIZIER NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 158,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 160,    Local,    Super Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 161,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 162,    Local,    Super Stock    NON VIP
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> PEDAL& BRACE CANNOT BE PAINTED
   Failed item 19. “Brake plunger installed per plans, Photos 8.26 & 8.30”.   Reason -> PLUNGER AND SPRING CANNOT BE PAINTED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 600,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 604,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 605,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 606,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 607,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 609,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 610,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 611,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 612,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 613,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 614,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 616,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 617,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 618,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 619,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 620,    Local,    Super Stock    NON VIP
   Failed item 5. “Rear kingpin washer stack per plans, Photo 3.26 “.   Reason -> NOT PER PLAN-WRONG KINGPIN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 621,    Local,    Super Stock    NON VIP
   Failed item 5. “Rear kingpin washer stack per plans, Photo 3.26 “.   Reason -> REAR KING PIN NOT PER PLAN-MISSING 2 “N” AND FENDER WASHERS
   Failed item 16. “New brake pad installed,  “.   Reason -> NEEDS NEW BRAKE PAD
   Failed item 18. “Cable pulley installed per plans, Photo 8.24”.   Reason -> MISSING LOCK WASHER
   Failed item 19. “Brake plunger installed per plans, Photos 8.26 & 8.30”.   Reason -> PLUNGER EYEBOLT NOT PER PLAN-MISSING LOCK WASHER
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 622,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 623,    Local,    Super Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 624,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 625,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 626,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 627,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 628,    Local,    Super Stock    NON VIP
   Failed item 14. “Stabilizer assembly per plans, Photos 6.7, 6.8, 6.11, 6.19 “.   Reason -> REAR STABILIZER/REMOVE “N” WASHER – NEEDS LOCK WASHER ON STABILIZER
   Failed item 19. “Brake plunger installed per plans, Photos 8.26 & 8.30”.   Reason -> NEED LOCK WASHER ON BRAKE EYEBOLT, NEEDS LOCK WASHER ON PLUNGER, LOCK WASHER ON BASE OF BRAKE PEDAL
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 629,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 632,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 633,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 634,    Local,    Super Stock    NON VIP
   Failed item 14. “Stabilizer assembly per plans, Photos 6.7, 6.8, 6.11, 6.19 “.   Reason -> REAR STABILIZER NOT PER PLAN
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 635,    Local,    Super Stock    NON VIP
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> NOT PER PLAN
   Failed item 18. “Cable pulley installed per plans, Photo 8.24”.   Reason -> MISSING “N” WASHER
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 636,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 637,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 638,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 639,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 640,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 643,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 644,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = R601,    Rally,    Super Stock    NON VIP
   Failed item 3. “Bushing installed per plans , Photo 3.5 & 3.7 “.   Reason -> WRONG KINGPIN-SHOULD BE 3-1/4 NOT 3-1/2
   Failed item 11. “Steering cable routing per plans, Photos 5.24, 5.27, 5.32 5.38(a) & (b) “.   Reason -> WRAPPED WRONG
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = R602,    Rally,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 615,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 159,    Local,    Super Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!

Car No. = 347,    Local,    Stock    NON VIP
   Failed item 6. “Steering hardware per plans, Photos 4.6, 4.10(a) & (b) “.   Reason -> NEEDS “N” WASHER UNDER FRONT STEERING PULLEY – STEERING EYEBOLT NOT PER PLAN
   Failed item 17. “Brake pedal hardware per plans, Photos 8.4, 8.12 & 8.18 “.   Reason -> BREAK PEDAL CAN NOT BE ALTERED
   Failed item 24. “Fixed weight hardware per plans, Photo 1.6”.   Reason -> WEIGHT BOLTS NEEDS TO BE AASBD ISSUED
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 321,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 313,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 355,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!

Car No. = 356,    Local,    Stock    VIP   But the following will be checked after shell installation
   item 30. “Screw in nose of the shell, Photo 12.11”.   Reason -> Check after body installed !!
   item 31. “Shell flush with bottom of floorboard ,  “.   Reason -> Check after body installed !!
   item 32. “Shell circumference of 39-1/2 inches,  “.   Reason -> Check after body installed !!